CBX Components in Development

Companies or individuals that provide parts/accessories/services for our CBXs.

Post Reply
CBX-tras
ICOA Member
ICOA Member
Posts: 460
Joined: Tue Feb 16, 2010 1:29 pm
Location: Clinton Twp, Michigan
Location: Clinton Twp., Michigan, USA

CBX Components in Development

Post by CBX-tras »

My associate (Kurt) and I are developing CBX components and we're letting the world know of our intentions, so the CBX community doesn't end up with several people attempting to make the same parts as we've seen in another example recently.

We welcome your interest and feedback and invite you to comment here to gauge our initial run quantities.

Here are a few of the things in process:

Idle adjuster screw with flex shaft (We've seen several broken or ready to break due to rust). The threaded portion and knob will be stainless steel.

Float bowl drain screws in stainless steel.

1979 CBX slide needles - 05F specific shape.

Gas tanks. Early model first. Steel, inside coated to prevent rust, sold in prime. Customer will need to source cap, latch, emblems and petcock.

Regards,

Larry Zimmer
ICOA Web Post/Pix/Video Archive Mgt
ICOA Web Post/Pix/Video Archive Mgt
Posts: 2295
Joined: Mon Dec 15, 2003 2:32 pm
Location: Brighton, MI
Location: Brighton, Mich
Contact:

Re: CBX Components in Development

Post by Larry Zimmer »

Thanks, JR
Larry Zimmer
cbxlarry@sbcglobal.net

User avatar
NobleHops
ICOA Member
ICOA Member
Posts: 3915
Joined: Mon Jan 25, 2010 7:17 am
Location: Tucson, Arizona, USA
Location: Tucson, Arizona, USA

Re: CBX Components in Development

Post by NobleHops »

Amazing!!
Nils Menten
Tucson, Arizona, USA
'82 CBX, among others.

steve murdoch icoa #5322
ICOA Member
ICOA Member
Posts: 4099
Joined: Tue Mar 04, 2003 9:12 am
Location: St. Catharines, On. Canada
Location: St. Catharines, On. Canada

Re: CBX Components in Development

Post by steve murdoch icoa #5322 »

That's great, JR.
It's nice to hear about any reproduction parts that will help in keeping these bikes running.

User avatar
Jeff Bennetts
Posting God
Posting God
Posts: 2485
Joined: Wed Mar 05, 2003 8:38 am
Location: Ohio, USA
Location: Ohio, USA

Re: CBX Components in Development

Post by Jeff Bennetts »

:thumupp:

tevan
ICOA Member
ICOA Member
Posts: 726
Joined: Sun Apr 25, 2010 8:47 am
Location: Charleston, Illinois, USA
Location: Charleston, Illinois, USA

Re: CBX Components in Development

Post by tevan »

Making tanks will be a big help. It is getting very hard to find a dent free ,rust free tank.

itsacbx
Forum Regular
Forum Regular
Posts: 183
Joined: Mon Apr 10, 2017 10:43 pm
Location: Edmonton Alberta Canada
Location: Edmonton Alberta Canada
Contact:

Re: CBX Components in Development

Post by itsacbx »

ANYONE MAKING THE REAR GRAB RAIL/TAILLIGHT SUPPORT RAIL AND THE TAILLIGHT MOUNT PLATE FOR 79/80's ?
AND THE RUBBER SLEEVES FOR THE REAR BLINKERS?

CBX-tras
ICOA Member
ICOA Member
Posts: 460
Joined: Tue Feb 16, 2010 1:29 pm
Location: Clinton Twp, Michigan
Location: Clinton Twp., Michigan, USA

Re: CBX Components in Development

Post by CBX-tras »

itsacbx wrote:
Sat Jan 14, 2023 8:31 pm
ANYONE MAKING THE REAR GRAB RAIL/TAILLIGHT SUPPORT RAIL AND THE TAILLIGHT MOUNT PLATE FOR 79/80's ?
AND THE RUBBER SLEEVES FOR THE REAR BLINKERS?
In my world, reproducing either of these wouldn't make a business case. They'd fall into the "find a good, used one and refurbish", category.

Since the rubber wire protector is black and mostly out of view, I've used 4 to 1 ratio shrink tube to simulate the part. Good enough until you can locate better, concours correct. I don't think that anyone would fault you for that.

Post Reply

Return to “CBX Parts & Accessory Suppliers, Dealerships, Mechanics, OEM Parts, Speciality CBX Shops”