4000rpm bog

CBX-tras
ICOA Member
ICOA Member
Posts: 460
Joined: Tue Feb 16, 2010 1:29 pm
Location: Clinton Twp, Michigan
Location: Clinton Twp., Michigan, USA

Re: 4000rpm bog

Post by CBX-tras »

Contact my business associate Kurt, for all your carburetor parts needs. Together, we've been putting assembling the best components available.
Just send him a message of your needs. Ships worldwide.

KMCarbuetor.com

Salman_z8
Forum Regular
Forum Regular
Posts: 68
Joined: Fri Oct 11, 2019 12:12 am
Location: Edmonton AB
Location: Canada

Re: 4000rpm bog

Post by Salman_z8 »

Carbs are back to stock.
Airbox mounted up, and finally lined up correctly, now that the correct breather hose was installed.
Started up right away, and runs pretty good now.
Took a few twists of the wrist, to prime the accelerator pump, once that came on line, it ran great.

It still has incorrect spark plugs, i will put in some d8ea tomorrow. And run it a few kms.

Something isnt right with the clutch. But thats for another day.
I might have to take the cover off and inspect.

The bike now does seem to be smoking once hot.
May be thats some of the sootburning off that got built up ( probably not ), but trying to be optimistic.
One day, i’ll have em all finished.

Salman_z8
Forum Regular
Forum Regular
Posts: 68
Joined: Fri Oct 11, 2019 12:12 am
Location: Edmonton AB
Location: Canada

Re: 4000rpm bog

Post by Salman_z8 »

Thank you for all the support folks.
The issue for which i had started this thread is now resolved.
One day, i’ll have em all finished.

daves79x
ICOA Technical Director
ICOA Technical Director
Posts: 4876
Joined: Sun Oct 01, 2006 8:05 am
Location: Knox, PA
Location: Knox, PA

Re: 4000rpm bog

Post by daves79x »

Don't worry about the smoke just yet. If the bike has laid up for a while, oil is burning out of the combustion chamber and possibly the exhaust, depending on prior treatment. Run it through several heat and cool cycles and it will stabilize. Not saying it won't be a smoker or use oil, but most don't after a proper re-commissioning.

What exactly is going on with your clutch?

Dave

Salman_z8
Forum Regular
Forum Regular
Posts: 68
Joined: Fri Oct 11, 2019 12:12 am
Location: Edmonton AB
Location: Canada

Re: 4000rpm bog

Post by Salman_z8 »

Not sure yet, if its a clutch issue, or worn/bent tranny components.
Shifting is hard, impossible to come out of first, whether to neutral or second, when coming to a stop.
Even while standing stationary, while in gear and holding the clutch, blipping the throttle can help shift.

But as soon as engine is turned off, tranny can shift again.

While riding, it will shift theough all gears, but not as smoothly as hondas usually do. But the counter shaft turning definitely helps the shifting, still crunchy though.

Clutch is adjusted. May be plates are stuck together, no clue yet, havnt looked.
One day, i’ll have em all finished.

daves79x
ICOA Technical Director
ICOA Technical Director
Posts: 4876
Joined: Sun Oct 01, 2006 8:05 am
Location: Knox, PA
Location: Knox, PA

Re: 4000rpm bog

Post by daves79x »

Have you started the clutch adjustment procedure by the manual, from the bottom adjuster under the little cap on the clutch cover, then work your way up? Sounds to me like the clutch is just plain not fully releasing.

Dave

heli_madken
Forum Regular
Forum Regular
Posts: 137
Joined: Wed Oct 21, 2020 12:09 pm
Location: Port William - Scotland
Location: Port William - Scotland

Re: 4000rpm bog

Post by heli_madken »

It does sound very much like my experience having bought an engine back to life after a long lay up, I initially adjusted the clutch by the book but it displayed the symptoms you have then after a few dozen miles did it again as Dave suggests and it was right as rain

Salman_z8
Forum Regular
Forum Regular
Posts: 68
Joined: Fri Oct 11, 2019 12:12 am
Location: Edmonton AB
Location: Canada

Re: 4000rpm bog

Post by Salman_z8 »

daves79x wrote:
Wed Mar 29, 2023 2:10 pm
Have you started the clutch adjustment procedure by the manual, from the bottom adjuster under the little cap on the clutch cover, then work your way up? Sounds to me like the clutch is just plain not fully releasing.

Dave
Yes i did. It does feel like as it doesnt disengage fully.
I have been very careful, as to not push it i into gears if it doesnt want to, to not incur any more damage or wear.

Once into service, i am hoping it will improve.

Meantime, i notices today, that the charging system needs attention as well lol
One day, i’ll have em all finished.

Salman_z8
Forum Regular
Forum Regular
Posts: 68
Joined: Fri Oct 11, 2019 12:12 am
Location: Edmonton AB
Location: Canada

Re: 4000rpm bog

Post by Salman_z8 »

heli_madken wrote:
Wed Mar 29, 2023 6:20 pm
It does sound very much like my experience having bought an engine back to life after a long lay up, I initially adjusted the clutch by the book but it displayed the symptoms you have then after a few dozen miles did it again as Dave suggests and it was right as rain
I have the same experience with other bikes in the past.
Fingers crossed
One day, i’ll have em all finished.

User avatar
FalldownPhil
ICOA Member
ICOA Member
Posts: 933
Joined: Fri Feb 10, 2006 11:25 pm
Location: Marina Del Rey, CA. USA
Contact:

Re: 4000rpm bog

Post by FalldownPhil »

Aftermarket clutch components have been know to cause these problems.
Are your fibers and steel plates stock??
Best,
Phil
When you are up to your ass in alligators it is sometimes difficult
to remember that your objective was to drain the swamp !!

Salman_z8
Forum Regular
Forum Regular
Posts: 68
Joined: Fri Oct 11, 2019 12:12 am
Location: Edmonton AB
Location: Canada

Re: 4000rpm bog

Post by Salman_z8 »

FalldownPhil wrote:
Thu Mar 30, 2023 5:33 pm
Aftermarket clutch components have been know to cause these problems.
Are your fibers and steel plates stock??
Best,
Phil
Hi phil

I cant say that i know whats in there for clutch plates.
I will ride it a few 100kms, and then see if i wana open it up,
Unless it improves.

The bike doesnt look abused, other than the crazy carb parts lol
One day, i’ll have em all finished.

Post Reply

Return to “CARBS: Cleaning, Rebuilding, Swaps, Aftermarket, Tuning, Syncing, and More”